Free Shipping

iFlight SucceX-A AIO F4 Flight Controller 40A Blheli_32 2-6S Brushless ESC Board compatible DJI Air Unit


To confirm that this part fits your vehicle, please enter your vehicle's details below.

  • Year:


    • Make:


      • Model:


        • Submodel:


          • Trim:


            • Engine:


              • Clear All
              This part is compatible with 0 vehicle(s).
              Show all compatible vehicles
              This part is compatible with 1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  PRODUCT DESCRIPTION

                  The SucceX-A F4 AIO(F4+40A) NEXT-GEN flight controller you need for your build. This FC is ready for anything with 5 uarts,4 motor outputs, 8Mb blackbox and a powerful F4 processor to run it all. Designed to work seamlessly with DJI’s new HD FPV system. To make things even simpler, the DJI Air unit can just be plugged into the AIO FC with the included wire harness. In addition, we added the popular and reliable USB Type-C instead of Micro USB and therefore the same standard than your DJI module.

                  Attention: This AIO-Board was specifically designed to run with a DJI Air Unit and takes advantage of DJI‘s latest Betaflight OSD pass-through! Because of space limitations we needed to take compromises and removed analog OSD support for this board! If you need analog OSD functionality, please check our latest releases.


                  FC // SucceX-A F4 AIO

                  • MCU: 168MHz STM32F405
                  • Gyro: MPU6000
                  • Blackbox: 8MB
                  • OSD Chip: NO (Analog OSD not available)
                  • OSD Betaflight: YES (Digital DJI Air Unit pass-through)
                  • BEC: 5V 2.5A  (3A MAX) / 10V 2.5A (3A MAX)
                  • Voltage sensor scale: 110
                  • Current sensor scale: 100
                  • Inverter for SBUS input (UART2-RX)
                  • Beeper pad : Yes
                  • RSSI input pad: No
                  • UARTs: 5
                  • Motor outputs: 4
                  • 8 pin for DJI air unit port (10V, GND, T1, R1, GND, R2I, T2, 5V)
                  • BLHeli32 Telemetry: RX4
                  • Input voltage: recommended 2-6S
                  • Target: STM32F405 (CLI config necessary; Check SETUP GUIDE above)
                  • Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm
                  • Dimensions:   40.5*43mm
                  • Weight: 11.4g
                  • USB type-C

                  Top Features:

                  • DJI Plug-and-Play – No need to solder tiny wires!

                  • Gyro Fusion – Zero delay Twin-Gyro filtering!

                  • Dual BEC 5V and 10V


                  ESC // SucceX 40A 2-6S
                  • MCU: STM32F051
                  • Up tp 48kHz PWM frequency
                  • Capacitance: 484uF
                  • Current Sensor: Yes
                  • Input: 2-6S LIPO
                  • Constant: 40A / Burst: 50A
                  • BlHeli32 telemetry: Yes
                  • BEC: No
                  • Supports up to Dshot1200, Proshot, Oneshot, Multishot 
                  • Target: iFlight-BL32-4IN1
                  • Mounting pattern: 30.5*30.5mm/Φ3mm
                  • Dimensions43*39mm (including the power pads)

                  Top Features:

                  – 6 layers double-sided PCB board

                  – 2oz 1.6mm thick power board

                  – 32bit STM32F051 MCU, 48kHz maximum clock speed

                  – TDK MLCC Low ESR ceramic capacitors

                  – Top grade TPN2R304PL MOSFET

                  Package Includes:

                  1 x SucceX-A F4 AIO

                  1 x Capacitor 470uF/50V

                  1 x XT60 12AWG cable

                  1 x Wire harness (plug&play) for DJI Air Unit

                  4 x M4 to M3 silicon grommets


                  Leave a Comment